Digital Dispensary

Product Sections


Best Sellers

'O' Ring for Thermostat

'O' Ring for Thermostat

0.55

Application: Series 1, 2 & 3 4cylinder engines.
Description: 'O' ring for sealing thermostat to cylinder head.
Approximate dimensions: outside diameter 55mm (2.2").
Original part number 01645
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gasket Exhaust Manifold to Down Pipe

Gasket Exhaust Manifold to Down Pipe

0.96

Application: Series 1, 2 & 3 four cylinder engines.
Description: Square flange gasket for exhaust. Used on various exhaust manifolds and on some pipe to pipe exhaust joints.
find out more

Thermostat 82 degrees

Thermostat 82 degrees

10.61

Application: Series 1 1.6ltr & 2.0ltr petrol engines, Defender 2.5 & 2.5TD diesel engines.

Description: Waxstat 82degree thermostat.

Original part number: 504560.

find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Gasket Oil Retaining Cap to Block

Gasket Oil Retaining Cap to Block

2.96

Application: Series 1 fitted with 1600cc petrol (gasolene) engine and 1954 only 2000cc petrol (gasolene) engine.
Description: Cork gasket for oil retaining cap to rear of cylinder block.
Approximate dimensions: internal diameter 108mm (4.25")
find out more

Steering Box Repair Kit

Steering Box Repair Kit

27.00

Application: Late Series 1, Series 2/2A and Series 3.

Description: Manual steering box repair kit suitable for both left hand drive and right hand drive vehicles. Kit contains 20x 9/32" diameter balls, 12x 3/8" diameter balls, 2x bearing races, 6x gaskets/shims, bush, 'o' ring and retainer for output shaft.

Back in stock.
find out more

Inner Wheel Hub Seal

Inner Wheel Hub Seal

4.28

Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

find out more

Fixings Kit for Water Pump

Fixings Kit for Water Pump

19.87

Application: Series One, 1948 to 1958.

Description: Set of fixings for water pump comprising the following parts;
6x 250517 bolt 1/4"BSF x 1.5", 1x 250518 bolt 1/4"BSF x 1.75", 1x 237150 bolt 1/4"BSF x 2.25", 2x set screw 5/16"BSW x 11/16" plus 8x 1/4" lock washers and 2x 5/16" lock washers.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > DISCOVERY 1 parts > Discovery 1 Electrical Parts
Page:  1  2   >   >>
Spider Bypass Link Cable Ref: AMR4956
Application: Discovery 1 1995 to 1998 approx, where fitted with original immobilisation and alarm system.
Description: Small wiring harness to bypass the "spider" .
See http://forums.lr4x4.com/index.php?showtopic=86 for full instructions on how to fit.

Price: 9.66 (11.59 Including VAT at 20%)



Spider Bypass Link Cable
Connector Kit for Bulb Holders Ref: ZZLRA102
Application: Single pole bulb holders on Defender 1995 onwards, Discovery 1, Discovery 2, Range Rover Classic late,and Range Rover 38A 1995 to 2001.
Description: Connection kit for replacing plug that connects to single pole bulb holder XPB100180.

Price: 3.67 (4.40 Including VAT at 20%)



Connector Kit for Bulb Holders
Connector Kit for Bulb Holder - 2 pole Ref: ZZLRA103
Application: Double pole bulb holders on Defender 1995 onwards, Discovery 1, Discovery 2, Range Rover Classic late,and Range Rover 38A 1995 to 2001.
Description: Connection kit for replacing plug that connects to double pole (stop/tail) bulb holder BAU5028L.

Price: 4.10 (4.92 Including VAT at 20%)



Connector Kit for Bulb Holder - 2 pole
Bulb Holder & Lead - Side Repeat Lamp Ref: ZZLRA608
Application: Defender 1995 onwards, Discovery 1 1995 onwards and Range Rover Classic 1993 onwards.
Description: Bulb holder and lead for side repeater indicator lamp. Equivalent to Land Rover part number STC966. Cable length 42cm (16.5").

Price: 27.88 (33.46 Including VAT at 20%)



Bulb Holder & Lead - Side Repeat Lamp
Headlamp Connector Ref: ZZDURITE53951
Application: Sealed beam and H4 bulbs.
Description: Connector kit for sealed beam and H4 headlamps.

Price: 3.01 (3.61 Including VAT at 20%)



Headlamp Connector
Battery Isolator Switch Ref: ZZGCU001
Application: Fairly universal.
Description: Battery isolator switch. Can be used as an additional security feature on early models (but not on later vehicles with excessive electronics as isolating battery may well disrupt normal functions on reconnection).
Can also be used for isolating auxilliary equipment such as winches etc.

Price: 4.54 (5.45 Including VAT at 20%)



Battery Isolator Switch
Bulb Holder Single Pole Ref: XBP100180
Application: Defender 1995 onwards, Discovery One, Discovery Two, Range Rover Two(38A) Freelander One.
Description: Bulb holder for single filament one pole bulbs. 2pin connector. Takes ZZLRA102 connector kit.
Approximate dimensions: overall length 45mm(1.8"), overall diameter 40mm(1.6")

Price: 1.85 (2.22 Including VAT at 20%)





Related products:
1. Connector Kit for Bulb Holders (Ref: ZZLRA102)
Bulb Holder Single Pole
V8 Waterproofing Kit Ref: ZZBA2840
Application: All V8 models with distributor ignition.

Description: Molded rubber boots for distributor and coil. Supplied with cable ties.

Price: 37.15 (44.58 Including VAT at 20%)



V8 Waterproofing Kit
Distributor Cap Lucas V8 Ref: STC8368
Application: All Rover V8 engines when fitted with Lucas distributor.
Description: Lucas DDB107 distributor cap.
Approximate dimensions: Overall diameter 105mm, height 75mm.

Price: 10.95 (13.14 Including VAT at 20%)



Distributor Cap Lucas V8
Rotor Arm Lucas V8 Ref: STC1857
Application: Electronic ignition versions of Lucas V8 Distributor.
Description: Portugues made rotor arm supposedly on original Lucas tooling. (Original Lucas item is no longer available and these are no longer in production).
Approximate dimensions: length 70.5mm (2.8"), height 24.2mm (0.95"), spindle diameter 14.6mm (0.57").

Price: 8.99 (10.79 Including VAT at 20%)



Rotor Arm Lucas V8
Digital Dispensary > DISCOVERY 1 parts > Discovery 1 Electrical Parts
Page:  1  2   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Pulley - Alternator/Dynamo

Pulley - Alternator/Dynamo

10.20

Application: Series3 and early Defender. Also possibly Sweries2A.

Description: Pulley for alternator and possibly some dynamos. Takes 'A' section belt.

Approximate dimensions: Overall diameter 69mm(2.7"), spindle diameter 9/16"(14mm), height 23mm(0.8")


find out more

Reverse Gear Assembly

Reverse Gear Assembly

92.08

Application: Series 1, Series 2 and Series 2A with part syncromesh gearbox.

Description: OE spec reverse gear assembly with bronze bush. Larger wheel has 20 teeth, smaller 17 teeth.

Approximate dimesions: Overall diameter 75mm(3"), internal diameter 20.8mm(0.82"), length 35mm(1.4")

Previous part number: 217389

find out more

Horn Button

Horn Button

14.42

Application: Late Series1 and early Series2.

Description: Reproduction horn switch mounted on side of steering column.

Approximate dimensions: Length 52mm(2"), width 38mm(1.5"), depth 25mm(1").

find out more

Lever Assemby for Throttle Linkage

Lever Assemby for Throttle Linkage

44.52

Application: Series 2A and Series 3 when Zenith carburrettor (or Weber conversion) is fitted.

Description: Lever assembly for throttle linkage, required when changing from Solex to Zenth. Supplied with bronze bush and ball.

Approximate dimensions: Overall length 132mm(5.2").

find out more

Locking Hasp for Fuel Cap

Locking Hasp for Fuel Cap

4.50

Application: Series 2a and Series 3.

Description: Locking hasp for fuel cap with 'ears'. Allows use of padlock to secure fuel cap.

Approximate dimensions: Mounting screw centres 70mm(2.75")

Old part number: GLR361

find out more

Bail Assembly

Bail Assembly

2.70

Application: Series 2A and Series 3.

Description: Retainer for glass bowl on side of lift pump on 4 cylinder models.

Approximate dimensions: Overall length 92mm, width 58mm.

find out more

Fuel Filler Cap

Fuel Filler Cap

26.46

Application: Series 2a and Series 3.

Description: Old stock Unipart 2 lug fuel filler cap. Supplied with seal,

Approximate dimensions: Overa;; diameter 96mm(3.8").

find out more

6 Way Lighting Switch - Military

6 Way Lighting Switch - Military

153.60

Application: Series3, Light Weight, 101 and Defender military models.

Description: Old stock Lucas 34259 six way lighting swith with facility for lock barrel (not supplied).


find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -