Digital Dispensary

Product Sections


Best Sellers

'O' Ring for Thermostat

'O' Ring for Thermostat

0.55

Application: Series 1, 2 & 3 4cylinder engines.
Description: 'O' ring for sealing thermostat to cylinder head.
Approximate dimensions: outside diameter 55mm (2.2").
Original part number 01645
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gasket Exhaust Manifold to Down Pipe

Gasket Exhaust Manifold to Down Pipe

0.96

Application: Series 1, 2 & 3 four cylinder engines.
Description: Square flange gasket for exhaust. Used on various exhaust manifolds and on some pipe to pipe exhaust joints.
find out more

Thermostat 82 degrees

Thermostat 82 degrees

10.61

Application: Series 1 1.6ltr & 2.0ltr petrol engines, Defender 2.5 & 2.5TD diesel engines.

Description: Waxstat 82degree thermostat.

Original part number: 504560.

find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Gasket Oil Retaining Cap to Block

Gasket Oil Retaining Cap to Block

2.96

Application: Series 1 fitted with 1600cc petrol (gasolene) engine and 1954 only 2000cc petrol (gasolene) engine.
Description: Cork gasket for oil retaining cap to rear of cylinder block.
Approximate dimensions: internal diameter 108mm (4.25")
find out more

Steering Box Repair Kit

Steering Box Repair Kit

27.00

Application: Late Series 1, Series 2/2A and Series 3.

Description: Manual steering box repair kit suitable for both left hand drive and right hand drive vehicles. Kit contains 20x 9/32" diameter balls, 12x 3/8" diameter balls, 2x bearing races, 6x gaskets/shims, bush, 'o' ring and retainer for output shaft.

Back in stock.
find out more

Inner Wheel Hub Seal

Inner Wheel Hub Seal

4.28

Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

find out more

Fixings Kit for Water Pump

Fixings Kit for Water Pump

19.87

Application: Series One, 1948 to 1958.

Description: Set of fixings for water pump comprising the following parts;
6x 250517 bolt 1/4"BSF x 1.5", 1x 250518 bolt 1/4"BSF x 1.75", 1x 237150 bolt 1/4"BSF x 2.25", 2x set screw 5/16"BSW x 11/16" plus 8x 1/4" lock washers and 2x 5/16" lock washers.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > RANGE ROVER Classic Parts > Range Rover Classic Fuel System
Page:  1  2  3   >   >>
Rebuild Kit for Stromberg CD175 Ref: ZZCDRK32
Application: Range Rover Classic 1976-1986, Defender 1982 - 1986, where fitted with twin CD175 carburetors.
Description: Rebuild kit for pair of CD175s. Contains all service items except the metering needles. These need to be ordered separately by carburetor specification number.


Price: 65.13 (78.16 Including VAT at 20%)





Related products:
1. Mixture Adjusting Tool CD175 (Ref: ZZB25860)
Rebuild Kit for Stromberg CD175
Float for CD175 Ref: 605833
Application: Rover V8 engines with CD175 carburetors.
Description: Genuine Zenith float.

Price: 9.50 (11.40 Including VAT at 20%)



Float for CD175
Twin 'SU' Carburetor Kit for V8 Ref: ZZFZX3010
Kit containing a pair of genuine SU carburetors plus all the fixings, adaptors etc to replace Stromberg CD175 carbs on V8 engines.


These kits are built to order and can take a few weeks to obtain.

Price: 575.00 (690.00 Including VAT at 20%)



Twin 'SU' Carburetor Kit for V8
Overhaul kit for Pair of HIF44 SU Carburetors Ref: ZZCRK268
Application: Rover V8 engine where fitted with twin HIF44 SU carburetors.
Description: Genuine SU boxed overhaul kit.

Price: 72.00 (86.40 Including VAT at 20%)



Overhaul kit for Pair of HIF44 SU Carburetors
Gasket Pack for SU HIF44 Carburetter Ref: WZX1505
Application: Rover V8 with SU HIF44 carbs.

Description: Original Equipment gasket pack to service one carburettor.

Price: 8.25 (9.90 Including VAT at 20%)



Gasket Pack for SU HIF44 Carburetter
Replacement Electric Fuel Pump - PRC3901 Ref: PRC3901
Facet electric petrol pump 476087N - made in the USA.

Application: Range Rover Classic 1974 to 1986, Series3 6cyl suffix B onwards, Series3 109V8, Defender 4cyl petrol and V8 with external fuel pump (up to about 1984/5)

Price: 60.80 (72.96 Including VAT at 20%)



Replacement Electric Fuel Pump - PRC3901
Replacement Fuel Pump - ETC7869 Ref: ETC7869
Application: Defender 2.5 Diesel with later type pump, 2.5 Turbo Diesel and 200TDI. Discovery 200TDi. Range Rover Classic 200TDi.

Description: Replacement mechanical lift pump made in England. This is the later type for the 2.5 Diesel, if your old pump does not look the same as this you will need the conversion kit STC1190.

Price: 28.50 (34.20 Including VAT at 20%)



Replacement Fuel Pump - ETC7869
Replacement Fuel Pump Kit Ref: STC1190D
Application: 2.5 litre naturally aspirated diesel, 2.5 litre turbo diesel, 200TDI. For use where existing pump does not look like ETC7869. (The original pump being no longer available).

Description: Replacement fule pump and fitting kit to allow fitting in place of original design of pump.

Price: 27.70 (33.24 Including VAT at 20%)



Replacement Fuel Pump Kit
Replacement Electric Fuel Pump - PRC7020 Ref: PRC7020
Replacement electric petrol pump of UK manufacture.

Application: Range Rover Classic 1986-1991 with carburettor V8, Defender 110 4cyl petrol and V8 with 'in tank' pump (from approx 1984/5 onwards).
This is the low pressure pump, it is not suitable for EFi engines.

Approximate dimensions: top plate diameter 80mm, in tank length 230mm.

Price: 40.42 (48.50 Including VAT at 20%)



Replacement Electric Fuel Pump - PRC7020
Replacement 'In Tank' Pump - PRC8318 Ref: PRC8318
Replacement electric petrol pump.

Application: Range Rover Classic 1986-1991 with EFi V8.
This is the high pressure pump, it is suitable for EFi engines.

Approximate dimensions: top plate diameter 80mm, in tank length 230mm.

Price: 28.00 (33.60 Including VAT at 20%)




People who bought this item also bought:
1. Mounting kit for ZZPWBRO12F Fuel Tank (Ref: ZZPWBRO12FFIX)
2. Replacement Fuel Tank for Classic Range Rover (Ref: ZZPWBRO12F)
3. Replacement Fuel Sender Unit for Range Rover (Ref: PRC8822KIT)
Replacement 'In Tank' Pump - PRC8318
Digital Dispensary > RANGE ROVER Classic Parts > Range Rover Classic Fuel System
Page:  1  2  3   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Pulley - Alternator/Dynamo

Pulley - Alternator/Dynamo

10.20

Application: Series3 and early Defender. Also possibly Sweries2A.

Description: Pulley for alternator and possibly some dynamos. Takes 'A' section belt.

Approximate dimensions: Overall diameter 69mm(2.7"), spindle diameter 9/16"(14mm), height 23mm(0.8")


find out more

Reverse Gear Assembly

Reverse Gear Assembly

92.08

Application: Series 1, Series 2 and Series 2A with part syncromesh gearbox.

Description: OE spec reverse gear assembly with bronze bush. Larger wheel has 20 teeth, smaller 17 teeth.

Approximate dimesions: Overall diameter 75mm(3"), internal diameter 20.8mm(0.82"), length 35mm(1.4")

Previous part number: 217389

find out more

Horn Button

Horn Button

14.42

Application: Late Series1 and early Series2.

Description: Reproduction horn switch mounted on side of steering column.

Approximate dimensions: Length 52mm(2"), width 38mm(1.5"), depth 25mm(1").

find out more

Lever Assemby for Throttle Linkage

Lever Assemby for Throttle Linkage

44.52

Application: Series 2A and Series 3 when Zenith carburrettor (or Weber conversion) is fitted.

Description: Lever assembly for throttle linkage, required when changing from Solex to Zenth. Supplied with bronze bush and ball.

Approximate dimensions: Overall length 132mm(5.2").

find out more

Locking Hasp for Fuel Cap

Locking Hasp for Fuel Cap

4.50

Application: Series 2a and Series 3.

Description: Locking hasp for fuel cap with 'ears'. Allows use of padlock to secure fuel cap.

Approximate dimensions: Mounting screw centres 70mm(2.75")

Old part number: GLR361

find out more

Bail Assembly

Bail Assembly

2.70

Application: Series 2A and Series 3.

Description: Retainer for glass bowl on side of lift pump on 4 cylinder models.

Approximate dimensions: Overall length 92mm, width 58mm.

find out more

Fuel Filler Cap

Fuel Filler Cap

26.46

Application: Series 2a and Series 3.

Description: Old stock Unipart 2 lug fuel filler cap. Supplied with seal,

Approximate dimensions: Overa;; diameter 96mm(3.8").

find out more

6 Way Lighting Switch - Military

6 Way Lighting Switch - Military

153.60

Application: Series3, Light Weight, 101 and Defender military models.

Description: Old stock Lucas 34259 six way lighting swith with facility for lock barrel (not supplied).


find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -